“Your walls form the foundation of your home. The weather out there will not be good for the exterior walls of your house. It isn’t enough to paint your wall to make it waterproof. After dealing with rain, snow, wind, dust, and heat of the outside environment, the paint will begin peeling off.”
Thus, waterproofing is the best way to ensure that your walls are protected and retain your house’s longevity. At the same time. It is vital to reduce your frequent renovation cost. So here are some of the simple steps for providing effective waterproofing solutions to your home.
Damp carpets and beneath wall coverings can be the most prominent place for mold and mildew growth. Finishing a basement without first dealing with the moisture problems can make health conditions worse and lead to significant damage. Interior waterproofing systems, installed by a professional contractor. Can keep moisture away throughout the home.
Step 1: Properly expose the outside part of the wall
To start with waterproofing your exterior walls. Make sure it is properly exposed to work on. Your house walls possess a lot of dirt, which creates an additional layer over the wall. Get rid of all the filth and dust from the walls. And before doing so. Remove all the drainage pipes and the old field tiles to get proper access to every corner and area of the wall.
Step 2: Thoroughly clean the walls
“The outer part of your home’s wall is usually covered with a lot of dust and dirt from the air. To ensure the efficiency of the entire process. You need to clear off the debris and dust thoroughly. The dirt and debris should be cleaned with a broom, brush. Or sandpaper. Then use a power washer to finish it off.”
Step 3: Check out for the cracks and fill them up
Cracks and holes can be found over time on your exterior walls. Follow up the cleaning process with a thorough look at the cracks and holes in the wall to make sure proper weatherproofing is done. You can fill them with cement.
Most homeowners get worried about cracks in the foundation. But the fact is, not all foundation cracks affect the home’s structural integrity. Sometimes cracks can be caused by shrinkage during the concrete curing process. These unsightly. Non-structural shrinkages. Commonly known as hairline cracks. Don’t put your home in immediate danger. But on the other hand. Structural cracks are serious business.
All over the internet and TV you find websites and programs with step-by-step guides for DIY foundation repair. But the truth is that a foundation should not be experimented on in a DIY project. Foundation repair requires years of experience and specialized tools. When it comes to foundation repair. Contact a foundation repair expert.
The cement mixture seals the cracks properly. Make sure you remove all the loose cement from the wall before you apply the cement.
Step 4: Add a layer of cement waterproofing sealer
If you want to make sure your wall is waterproof. You need to apply the cement waterproof. After applying the cement to the crevices. Let it dry. Then apply the waterproof paint seal to the walls. Let it become dry after that.
Step 5: Pick the right water-proofer
There are a lot of products that are waterproof. You have to pick the right one for the wall. The water-proofer should be chosen based on whether it is a concrete wall or a silicate-based one.
It is possible to choose between a silicate-based concrete sealer and a concrete waterproof coating. Pick a plaster waterproof Additive that will add strength to your walls.
Step 6: Apply the water-proofer
Use a brush or roller to apply the water-proofer to the walls. If you want to apply more than one layer. Give a thin coat first. Add the second coating after the first one is dry.
Step 7: Apply tar and heavy-duty membrane
If you want to add more strength to the layer. You need to use a tar-based pitch after the drying of the cement waterproofer. It should be applied to your exterior wall.
After that. You need to apply a heavy-duty plastic or rubber membrane. which will ensure the proper care of the walls.
Step 8: Consider adding gravel
To lay the drainage pipes, you need a base beneath the footer. The drainage pipes are going to be supported by a gravel base. Gravel is long-lasting and provides enhanced protection.
You need to lay the gravel along with the drainage pipe cover. Go near the footer and level the gravel. Make sure the pipe is covered for at least 3 inches.
Step 9: Add a fabric barrier
A fabric barrier is needed to secure the pipe. Ensuring a fabric barrier is going to prevent the formation of dirt and keep your system running. Then build the top of the dirt relatively high and allow it to settle for some time. Slope the ground away from the walls for the run-off after
Conclusion:
Good waterproofing gives your home a new life and strength to deal with outside issues. Magicrete can help you find good solutions for your walls. At a very low and affordable price. Magicrete has quality service and proper weatherproofing.
